LED motion sensor dimming light Stair streamline light under cabinet night light flexible LED Strip 12V Tape power supply
Important note: The positive and negative terminals of the power supply input of the controller cannot be reversed, the red wire V+ is connected to the positive electrode of the switching power supply, and the blue (or black wire) V- is connected to the negative electrode of the switching power supply.
Note: 1-You need buy the Power supply & white strip lights and addressable strip lights.
2-The 2 wires warm white /cold strip lights use to 1-36 channel inside the stair steps.
3-The Multi colored light is 3 wires addressable RGB strip lights 150 LEDs/5 meter, The 3 wires addressable strip lights use to 2 sides stair or railing for 7 color chasing effect
4-There are detailed installation instructions below the details page. Currently this product does not come with instructions. If you have any questions, please contact online customer service.
5-All light strips in this link are 5 meters per roll, please purchase according to your needs.
6-We sell power extension cords, but we do not sell connection cords for light strips. Please purchase them separately.
Product packaging LED Controller set include:
1 * 36 channel LED Controller
2 * Motion Sensors (white)
Product description:
36-channel multi-function LED controller with two sensors, which can drive 2 kinds of LED lights, one is a dreamcolor light that supports a universal SPI single-wire chip, such as the universal 1903, 1909, 1912, TM1812, WS2811, 16703, WS2812B, 8205, 8206 and so on full-color pixel LED lights, the control system at the lower left corner of DO1, GND, DO2, GND with 2 parallel output terminals, can be connected to the left and right sides of the stairs lights. The output terminals on both sides of the controller are for the single-color light strips used on the 36-way stair tread, the number of light strips can be adjusted. The function setting of the induction controller is selected by the buttons. The setting is displayed through the 4-digit digital tubes on the left.
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()
♦♦How to set up the program?
The display panel and key function list:
![]()
In the initial state of power on, the digital tube displays: XXXL, the XX on the left is the running speed of the dreamcolor lights on both sides of the stairs, 01-99, 01 is the fastest, 99 is the slowest.
Method of adjusting parameters by keys: In the initial XXXL display state,press the button “SET” into the setting parameter state, adjust the state value by pressing the two buttons of “SP- SP+”, then press the button “SET” again getting into the next menu adjustment state, the displayed state lists are as follows:
![]()
LXXX 010-800 Set The Pixel number of segment length of dreamcolor light strips on both sides of stairs, the maximum number is 800, press two buttons of “SP-SP+” to adjust, after finishing, continue to press “SET” getting into the next step,LPXX 01-07 is for the side panel light strip color is also adjusted by “SP- and SP+”, after finishing, then press SET getting into the next setting, 01 white 02 red 03 green 04 blue 05 yellow 06 purple 07 green LHXX 01-99 is for side dreamcolor light strip flashing speed,FXXX 010-800 Set the Number of stair step white light strips,
![]()
maximum 800 stairs FPXX stairs’ light effect, there is only 1 transition effect at the moment FHXX the speed of the stair white light turns on/off step by step
![]()
EEXX 01-99 seconds，adjusts the delay time when people walk through and stay on. When the delay time is up, the side panel light strip and stair light strip are extinguished gradually.
![]()
After finishing the adjustment of the parameters, press the “SET” button one last time, the parameter display will return to the XXXL display state, and it will automatically save the set parameters to the control system, the next time it will work according to the newly set parameters.
